Eva Fountain - Assembly Plan
Assembly diagram
1 - Lid
2 - High density ceramic filter
3 - Ceramic joint
4 - Upper tank
5 - Ceramic nut
6 - Cup for fixing the filter cartridge
7 - Filter cartridge
8 - Large bowl
9 - Lower tank receiving filtered water
10 - Basket of blue minerals
11 - Green IRL part (for fountains with BEP magnetic system)
12 - Faucet
13 - Faucet nut
14 - Base
1 - Lid
2 - High density ceramic filter
3 - Ceramic joint
4 - Upper tank
5 - Ceramic nut
6 - Cup for fixing the filter cartridge
7 - Filter cartridge
8 - Large bowl
9 - Lower tank receiving filtered water
10 - Basket of blue minerals
11 - Green IRL part (for fountains with BEP magnetic system)
12 - Faucet
13 - Faucet nut
14 - Base
Remove the protections from your EVA Fountain then rinse all the elements with clean water.
Put the ceramic in the tank with a central hole (n°4), the interior seal (n°3) of the ceramic must be positioned inside the tank (n°4). Screw the butterfly (n°5) of the ceramic, without forcing, finally rinse under clear tap water.
Take the filter cartridge (n°7) and follow the instructions (page 21).
Remove its packaging, then immerse it in a container filled with water to release air bubbles (2 to 3 minutes).
During this operation, prepare the base (n°14) on which you will place the second tank (n°9) for receiving filtered water.
Proceed to screwing the tap (n°12), insert it into the hole provided. There are 2 seals for sealing: 1 inner seal + 1 outer seal, position them correctly to obtain the desired seal. The flat parts of the joints must be positioned along the tank.
Take the nut (rounded side to screw against the joint), screw without forcing and above all without crushing the joints.
Put the ceramic in the tank with a central hole (n°4), the interior seal (n°3) of the ceramic must be positioned inside the tank (n°4). Screw the butterfly (n°5) of the ceramic, without forcing, finally rinse under clear tap water.
Take the filter cartridge (n°7) and follow the instructions (page 21).
Remove its packaging, then immerse it in a container filled with water to release air bubbles (2 to 3 minutes).
During this operation, prepare the base (n°14) on which you will place the second tank (n°9) for receiving filtered water.
Proceed to screwing the tap (n°12), insert it into the hole provided. There are 2 seals for sealing: 1 inner seal + 1 outer seal, position them correctly to obtain the desired seal. The flat parts of the joints must be positioned along the tank.
Take the nut (rounded side to screw against the joint), screw without forcing and above all without crushing the joints.
Take the basket blue (n°10) filled with minerals and rinse it under tap water to remove excess mineral dust and place it in the center of the second tray (n°9).
For BEP models, the magnetic disk white is already installed in the blue basket (n°10), you just need to add the green coin IRL (No. 11).
Place the large cup (n°8) on the second tray (n°9)
Place the cartridge (n°7) under tap water to finish purging it, black water may flow out due to the activated carbon, as soon as the water is clear your cartridge is ready for use.
Screw it filter cartridge (n°7) on the small cup (n°6) (fixing cup) and insert it into its location.
Then place the bin with the ceramic (n°4+n°2+n°3+n°5) on the large dish (n°8) and place the lid (n°1) on top of the fountain
Your fountain is ready.
Put water in the upper tank (n°4) and let it filter.
After assembly, YOU MUST PERFORM 4 FILTRATION CYCLES before consuming the water: fill your upper tank for the first time, let the water flow into the lower tank and give thefiltered water to your plants. Repeat this operation three times.
For BEP models, the magnetic disk white is already installed in the blue basket (n°10), you just need to add the green coin IRL (No. 11).
Place the large cup (n°8) on the second tray (n°9)
Place the cartridge (n°7) under tap water to finish purging it, black water may flow out due to the activated carbon, as soon as the water is clear your cartridge is ready for use.
Screw it filter cartridge (n°7) on the small cup (n°6) (fixing cup) and insert it into its location.
Then place the bin with the ceramic (n°4+n°2+n°3+n°5) on the large dish (n°8) and place the lid (n°1) on top of the fountain
Your fountain is ready.
Put water in the upper tank (n°4) and let it filter.
After assembly, YOU MUST PERFORM 4 FILTRATION CYCLES before consuming the water: fill your upper tank for the first time, let the water flow into the lower tank and give thefiltered water to your plants. Repeat this operation three times.
EMPTY ALL OF THE WATER IN THE LOWER TRAY (tray where the tap is located) AT THE END OF EACH CYCLE After these filtrations, YOUR EVA FOUNTAIN IS READY…