Assembly diagram
1 - Cover
2 - High density ceramic filter
3 - Ceramic gasket
4 - Upper tank
5 - Nut of the ceramic
6 - Cup for fixing the filter cartridge
7 - Filter cartridge
8 - Large cup
9 - Lower tank receiving filtered water
10 - Basket of blue minerals
11 - Green IRL piece (for fountains with BEP magnetic system)
12 - Faucet
13 - Faucet nut
14 - Base
1 - Cover
2 - High density ceramic filter
3 - Ceramic gasket
4 - Upper tank
5 - Nut of the ceramic
6 - Cup for fixing the filter cartridge
7 - Filter cartridge
8 - Large cup
9 - Lower tank receiving filtered water
10 - Basket of blue minerals
11 - Green IRL piece (for fountains with BEP magnetic system)
12 - Faucet
13 - Faucet nut
14 - Base
Remove the protections from your EVA Fountain then rinse all the elements with clean water.
Put the ceramic in the tank with a central hole (n°4), the interior seal (n°3) of the ceramic must be positioned inside the tank (n°4). Screw the butterfly (n°5) of the ceramic, without forcing, finally rinse under clear tap water.
Take the filter cartridge (n°7) and follow the instructions for use (page 21).
Remove its packaging, then immerse it in a container filled with water to evacuate the air bubbles (2 to 3 minutes).
During this operation, prepare it base (n°14) on which you will place the second tank (n°9) for receiving filtered water.
Proceed to screw the tap (n°12), insert it into the hole provided. There are 2 seals for sealing: 1 inner seal + 1 outer seal, position them correctly to obtain the desired seal. The flat parts of the joints must be positioned along the tank.
Take the nut (rounded side to screw against the joint), screw without forcing and above all without crushing the joints.
Put the ceramic in the tank with a central hole (n°4), the interior seal (n°3) of the ceramic must be positioned inside the tank (n°4). Screw the butterfly (n°5) of the ceramic, without forcing, finally rinse under clear tap water.
Take the filter cartridge (n°7) and follow the instructions for use (page 21).
Remove its packaging, then immerse it in a container filled with water to evacuate the air bubbles (2 to 3 minutes).
During this operation, prepare it base (n°14) on which you will place the second tank (n°9) for receiving filtered water.
Proceed to screw the tap (n°12), insert it into the hole provided. There are 2 seals for sealing: 1 inner seal + 1 outer seal, position them correctly to obtain the desired seal. The flat parts of the joints must be positioned along the tank.
Take the nut (rounded side to screw against the joint), screw without forcing and above all without crushing the joints.
Take the filled basket blue (n°10) of minerals and rinse it under tap water to eliminate excess mineral dust and place it in the center of the second bin (n°9).
For BEP models, the white magnetic disk is already installed in the blue basket (n°10), you just need to add the green piece IRL (n°11) to the center of the lid of the basket.
Place the large cup (n°8) on the second bin (n°9)
Put the cartridge (n°7) under tap water to finish purging it, black water may flow out due to the activated carbon, as soon as the water is clear your cartridge is ready for use.
Screw the cartridge filter (n°7) on the small cup (n°6) (fixing cup) and insert it into its location.
Then place the tank with the ceramic (n°4+n°2+n°3+n°5) on the large cup (n°8) and place the cover (n°1) on the above the fountain
Your fountain is ready.
Put water in the upper tank (n°4) and let it filter.
After assembly, YOU MUST PERFORM 4 FILTRATION CYCLES before consuming the water: fill your upper tank for the first time, let the water drain in the lower tray and give thefiltered water to your plants. Repeat this operation three times.
For BEP models, the white magnetic disk is already installed in the blue basket (n°10), you just need to add the green piece IRL (n°11) to the center of the lid of the basket.
Place the large cup (n°8) on the second bin (n°9)
Put the cartridge (n°7) under tap water to finish purging it, black water may flow out due to the activated carbon, as soon as the water is clear your cartridge is ready for use.
Screw the cartridge filter (n°7) on the small cup (n°6) (fixing cup) and insert it into its location.
Then place the tank with the ceramic (n°4+n°2+n°3+n°5) on the large cup (n°8) and place the cover (n°1) on the above the fountain
Your fountain is ready.
Put water in the upper tank (n°4) and let it filter.
After assembly, YOU MUST PERFORM 4 FILTRATION CYCLES before consuming the water: fill your upper tank for the first time, let the water drain in the lower tray and give thefiltered water to your plants. Repeat this operation three times.
EMPTY ALL OF THE WATER IN THE LOWER TRAY (tray where the tap is located) AT THE END OF EACH CYCLE After these filtrations, YOUR EVA FOUNTAIN IS READY…